Exploring Plumbing Fundamentals When You Install a Bathtub
Exploring Plumbing Fundamentals When You Install a Bathtub
Blog Article
This great article which follows in relation to How to Install a Bathtub is immensely fascinating. Try it and make your own personal assumptions.
Installing a bath tub isn't specifically brain surgery, but it does need strong plumbing, carpentry, and also occasionally, tiling skills. Replacing an old bathtub with a new one is also a moderately challenging task. If the old tub is readily available, the project can relocate speedily; if you need to open a wall to remove the old bathtub and position the brand-new tub, the job is much harder. In either case, the job is within a house handyman's skills, although you will certainly require a helper to move out the old tub and embeded in the new one. Ensure you have actually certified yourself for the work as well as fit attempting it. Instead of hiring a service provider to take control of a halfway-completed project, it is much better to consider employing one prior to you begin. Possibilities are you may need a specialist plumber to make tube links.
This write-up will certainly aid you mount a new bathtub in your bathroom if you have actually currently bought a brand-new tub and also don't require to alter the plan of your previous water system pipelines.
Your tools and also material list need to comprise the following:
Getting ready for the Setup
To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's directions. Next off, fit the faucets or mixer to the tub. When fitting the faucet block, it is very important to see to it that if the tap comes with a plastic washing machine, it is fitted in between the bath and the faucets. On a plastic bathroom, it is also practical to fit a supporting plate under the taps system to avoid pressure on the tub.
Fit the versatile faucet ports to the bottom of the two faucets making use of 2 nuts and olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet through the hole in the bath. Utilize the nut supplied by the manufacturer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit completion of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you use all of the supplied washers.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom should currently be ready to be fitted in its last position.
Removing Old Touches
If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is disconnect the water. After doing so, turn on the faucets to drain any type of water remaining in the system. The process of getting rid of the existing taps can be rather problematic as a result of the restricted accessibility that is often the instance.
Use a container wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a cloth all set for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, use the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to quit the solitary faucets from transforming during this procedure. As soon as the taps have actually been eliminated, the holes in the bath/basin will have to be cleansed of any old securing substance.
Before proceeding to fit the brand-new taps, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new faucets, after that a shank adapter is required for the brand-new faucets to fit.
Setting up the Tub
Making use of both wood boards under its feet, put the bathtub in the called for placement. The wooden boards are handy in evenly spreading the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four tiny points.
The following objective is to guarantee that the bath tub is leveled all round. This can be attained by checking the level and also adjusting the feet on the bath tub up until the spirit level checks out level.
To install taps, fit all-time low of the furthest flexible tap adapter to the ideal supply pipe by making a compression join; after that do the very same for the various other faucet.
Turn on the water and check all joints as well as brand-new pipework for leaks and also tighten them if necessary. Fill the tub as well as likewise inspect the overflow outlet as well as the typical outlet for leaks.
Ultimately, fix the bathroom paneling as described in the producer's instruction manual. Tiling as well as securing around the tub ought to wait till the tub has been made use of at least once as this will certainly resolve it into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will certainly need a plastic connector to avoid damages to the string. One end of the connector fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you require to fit a monobloc, after that you will need decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washers remain in area in between the faucet and also the sink. Safeguard the faucet in place with the manufacturer provided backnut. Once the tap is safely in place, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with regular tap ports. The former type ought to be attached to the tap finishes initially, tightening just by hand. The supply pipes can later on be attached to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Tiling Around the Bathtub
In the location where the bath fulfills the tile, it is necessary to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to split a rigid seal, triggering the water to pass through the wall between the bathroom as well as the tiling, resulting in difficulties with wetness and also possible leaks to the ceiling below.
You can select from a selection of coloured sealers to blend in your components and also fittings. They are sold in tubes as well as cartridges, and can securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Remember to constantly fill the tub with water prior to securing, to permit the movement experienced when the tub remains in usage. The sealer can crack fairly early if you do not take into consideration this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally quickly available on the market. It is a good idea to fit the ceramic tiles utilizing waterproof or waterproof glue as well as cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our excerpt about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround. Thanks a lot for spending some time to read through our short article. So long as you appreciated our page if you please be sure to pass it around. Thanks so much for taking the time to read it.
Stress-free fix? Contact. Report this page